Upgrade to Pro — share decks privately, control downloads, hide ads and more …

[4/6] Bipolar effects and bandgap

[4/6] Bipolar effects and bandgap

Andrei Novitskii

May 21, 2021
Tweet

More Decks by Andrei Novitskii

Other Decks in Education

Transcript

  1. Лекция «Введение в физику полупроводников» / 8 августа 2022 г.

    3 Bipolar Seebeck and conductivity The Seebeck coefficient is dramatically affected because the minority charge carriers add a Seebeck voltage of opposite sign as the majority carriers greatly reducing the thermopower 𝛼 . The contribution of each charge carrier to the total Seebeck coefficient is weighted by the electrical conductivity:[1] 𝛼𝑡𝑜𝑡𝑎𝑙 = 𝜎𝑚𝑎𝑗𝑜𝑟 𝛼𝑚𝑎𝑗𝑜𝑟 − 𝜎𝑚𝑖𝑛𝑜𝑟 𝛼𝑚𝑖𝑛𝑜𝑟 𝜎𝑚𝑎𝑗𝑜𝑟 + 𝜎𝑚𝑖𝑛𝑜𝑟 The electrical conductivity is least affected because both electrons can holes contribute to the electrical transport with the same sign: 𝜎𝑡𝑜𝑡𝑎𝑙 = 𝜎𝑚𝑎𝑗𝑜𝑟 + 𝜎𝑚𝑖𝑛𝑜𝑟 = 𝑒𝑛𝑚𝑎𝑗𝑜𝑟 𝜇𝑚𝑎𝑗𝑜𝑟 + 𝑒𝑛𝑚𝑖𝑛𝑜𝑟 𝜇𝑚𝑖𝑛𝑜𝑟 Reminder: for p-type holes are the major charge carriers for n-type electrons are the major charge carriers
  2. Лекция «Введение в физику полупроводников» / 8 августа 2022 г.

    4 Bipolar Hall constant The Hall voltage, which is also opposite for electrons and holes, is also compensated when both electrons and holes are present making the apparent Hall carrier concentration 𝑛𝐻 = 1 𝑒𝑅𝐻 increase much faster than the real majority carrier concentration. The individual contributions are even more strongly weighted by the electrical conductivity (mobility) than is the Seebeck coefficient (note that in this notation 𝜇 > 0 for holes and 𝜇 < 0 for electrons): 𝑅𝐻 = 1 𝑒𝑛𝐻 = 𝜎𝑚𝑎𝑗𝑜𝑟 𝜇𝑚𝑎𝑗𝑜𝑟 − 𝜎𝑚𝑖𝑛𝑜𝑟 𝜇𝑚𝑖𝑛𝑜𝑟 𝜎𝑚𝑎𝑗𝑜𝑟 + 𝜎𝑚𝑖𝑛𝑜𝑟 2 Reminder: for p-type holes are the major charge carriers for n-type electrons are the major charge carriers
  3. Лекция «Введение в физику полупроводников» / 8 августа 2022 г.

    5 Bipolar electronic thermal conductivity The thermal conductivity is also affected by the bipolar effect, but it is often not noticed because of the lattice contribution. Because there are more electron-hole pairs at high temperature then low temperature, in a temperature gradient there will be an effect of absorbing heat at the hot end by creating electron-hole pairs and releasing heat at the cold end when they recombine: 𝜅𝑒𝑙 = 𝜎𝑚𝑎𝑗𝑜𝑟 𝐿𝑚𝑎𝑗𝑜𝑟 𝑇 − 𝜎𝑚𝑖𝑛𝑜𝑟 𝐿𝑚𝑖𝑛𝑜𝑟 𝑇 + 𝛼𝑚𝑎𝑗𝑜𝑟 + 𝛼𝑚𝑖𝑛𝑜𝑟 2 𝜎𝑚𝑎𝑗𝑜𝑟 𝜎𝑚𝑖𝑛𝑜𝑟 𝑇 𝜎𝑚𝑎𝑗𝑜𝑟 + 𝜎𝑚𝑖𝑛𝑜𝑟 where the last term can be considered the bipolar thermal conductivity that increases exponentially with temperature as 𝑒 Τ 𝐸𝑔 𝑘𝐵𝑇. Reminder: for p-type holes are the major charge carriers for n-type electrons are the major charge carriers
  4. Лекция «Введение в физику полупроводников» / 8 августа 2022 г.

    6 Seebeck coefficient peak and bandgap Doping changes temperature dependence of 𝛼 (from lightly doped in blue to heavily doped in red), but the maximum of 𝛼 value is limited by 𝐸𝑔:[2] 𝐸𝑔 = 2𝑒 𝛼max 𝑇max This equation can be reasonably accurate when both electrons and holes have similar weighted mobility. If one type of carriers exhibits higher weighted mobility, it will have a stronger influence and affect the estimation of band gap.
  5. Лекция «Введение в физику полупроводников» / 8 августа 2022 г.

    7 Seebeck coefficient peak and bandgap This can be corrected by using ratio of the weighted mobilities:[3] 𝐴 = 𝜇𝑤,𝑚𝑎𝑗𝑜𝑟 𝜇𝑤,𝑚𝑖𝑛𝑜𝑟 = 𝜇𝑚𝑎𝑗𝑜𝑟 𝜇𝑚𝑖𝑛𝑜𝑟 𝑚𝑚𝑎𝑗𝑜𝑟 ∗ 𝑚𝑚𝑖𝑛𝑜𝑟 ∗ Τ 3 2 The following figure can be used to estimate the error from the bandgap equation. When the Seebeck peak is greater than 150 µV/K this method for estimation of the bandgap at high temperature is likely to be accurate. For details see Refs. [2,3].
  6. Лекция «Введение в физику полупроводников» / 8 августа 2022 г.

    8 Intrinsic region in 𝜎 and bandgap 𝜎 = 𝑒𝑛𝜇 (1) 𝜎 ∝ 𝑇 Τ 3 2+𝑚𝑒 Τ −Δ𝐸𝑑 2𝑘𝐵 (2) 𝜎 ∝ 𝑇𝑚 (3) 𝜎 ∝ 𝑇 Τ 3 2+𝑚𝑒 Τ −𝛼𝑡 2𝑘𝐵𝑒 Τ −Δ𝐸𝑔 0 2𝑘𝐵 assuming 𝐸𝑔 𝑇 = 𝐸𝑔 0 + 𝛼𝑡 𝑇, where 𝛼𝑡 is thermal coefficient. Intrinsic region (3) Extrinsic region (2) ln𝜎 𝑇−1 𝑇𝑑 −1 𝑇𝑖 −1 − Δ𝐸𝑔 0 2𝑘𝐵 − Δ𝐸𝑑 2𝑘𝐵 𝑇 (K) 𝐸𝑔 (𝑇) (eV) 𝐸𝑔 (0) 𝐸𝑔 0 Freeze out region (1)
  7. Лекция «Введение в физику полупроводников» / 8 августа 2022 г.

    9 Optical bandgap: direct bandgap The absorption coefficient 𝛼 is derived from the probability of transition from 𝐸 to 𝐸′, the occupied density of states at 𝐸 in the VB from which electrons are excited, and the unoccupied density of states in the CB at 𝐸 + ℎ𝜐. Near the band edges, the density of states can be approximated by a parabolic band, and 𝛼 rises with the photon energy following 𝛼ℎ𝜐 = 𝐴 ℎ𝜐 − 𝐸𝑔, where 𝐴 is the constant related to the electron and hole effective mass and refractive index.[4]
  8. Лекция «Введение в физику полупроводников» / 8 августа 2022 г.

    10 Optical bandgap: indirect bandgap In indirect bandgap semiconductors, the photon absorption for photon energies near 𝐸𝑔 requires the absorption and emission of phonons during the absorption process (see Fig.). Thus, the absorption corresponds to a photon energy of 𝐸 + ℎ𝜗, which represents the absorption of a phonon with energy ℎ𝜗. For the latter, 𝛼 is proportional to ℎ𝜐 − 𝐸𝑔 − ℎ𝜗 2 . Once the photon energy reaches 𝐸 + ℎ𝜗, then the photon absorption process can also occur by phonon emission, for which the absorption coefficient is larger than that for phonon absorption.[4]
  9. Лекция «Введение в физику полупроводников» / 8 августа 2022 г.

    11 Optical bandgap: degenerate semiconductors In degenerate semiconductors, the Fermi level 𝐸𝐹 is in a band, for example, in the CB for a degenerate n-type semiconductor. Electrons in the VB can only be excited to states above 𝐸𝐹 in the CB rather than to the bottom of the CB. The absorption coefficient then depends on the free-carrier concentration since the latter determines 𝐸𝐹. Fundamental absorption is then said to depend on band filling, and there is an apparent shift in the absorption edge, called the Burstein–Moss shift. Furthermore, in degenerate indirect semiconductors, the indirect transition may involve a non- phonon scattering process, such as impurity or electron-electron scattering, which can change the electron’s wavevector 𝑘. Thus, in degenerate indirect bandgap semiconductors, absorption can occur without phonon assistance and the absorption coefficient becomes 𝛼 ∝ ℎ𝜐 − 𝐸𝑔 + Δ𝐸𝐹 2 , where Δ𝐸𝐹 is the energy depth of 𝐸𝐹 into the band measured from the band edge.[4]
  10. Лекция «Введение в физику полупроводников» / 8 августа 2022 г.

    12 Optical bandgap: Urbach rule Heavy doping of degenerate semiconductors normally leads to a phenomenon called bandgap narrowing and bandtailing. Bandtailing means that the band edges at 𝐸𝑣 and 𝐸𝑐 are no longer well- defined cut-off energies, and there are electronic states above 𝐸𝑣 and below 𝐸𝑐 where the density of states falls sharply away with energy from the band edges. Consider a degenerate direct bandgap p-type semiconductor. One can excite electrons from states below 𝐸𝐹 in the VB, where the band is nearly parabolic, to tail states below 𝐸𝑐, where the density of states decreases exponentially with energy into the bandgap, away from 𝐸𝑐. Such excitations lead to 𝛼 depending exponentially on ℎ𝜐, a dependence that is called the Urbach rule, given by 𝛼 = 𝛼0 𝑒 ℎ𝜐−𝐸0 Δ𝐸 where 𝛼0 and 𝐸0 are material-dependent constants, and Δ𝐸, called the Urbach width, is also a material dependent constant.[4]
  11. Лекция «Введение в физику полупроводников» / 8 августа 2022 г.

    13 Optical bandgap: Kubelka-Munk relation Kubelka Munk theory derives a simple relation between the fraction of reflected light (𝑅) and the absorption coefficient (𝛼): 𝐹 𝑅 = 1 − 𝑅 2 2𝑅 = 𝛼 ෩ 𝐾 where 𝑅 is the diffuse reflectance of the sample as referred to a non-absorbing standard, 𝛼 is the molar absorption coefficient, ෩ 𝐾 is the diffuse reflection coefficient (unknown parameter).[5] For particle sizes greater than the light wavelengths measured, the scattering coefficient is understood to be approximately independent of frequency.
  12. Лекция «Введение в физику полупроводников» / 8 августа 2022 г.

    14 Optical bandgap: bandgap estimation In summary. For direct transitions: 𝛼ℎ𝜐 ∝ ℎ𝜐 − 𝐸𝑔 Τ 1 2 for ℎ𝜐 > 𝐸𝑔 according to the Tauc method.[6,7] In some studies authors used the 𝛼2 vs. ℎ𝜐 plot for estimation of the direct bandgap. But both methods give similar results within the measurement uncertainty. In the case of indirect transition: 𝛼ℎ𝜐 ∝ ℎ𝜈 − 𝐸𝑔 2 Some works suggest 𝛼 ∝ ℎ𝜈 − 𝐸𝑔 2 , but as was the case in direct gaps, the results do not change significantly. Thus, optical bandgap, can be estimated using the Tauc method where 𝛼ℎ𝜐 𝑛 (𝑛 = 2 for direct transitions and 𝑛 = Τ 1 2 for indirect) plotted versus photon energy ℎ𝜐 and is extrapolated to zero (normalized) absorption. The zero is determined by either normalizing the sample to the minimum absorption coefficient value or by fitting and subtracting the free carrier absorption contribution: 𝛼𝐹𝐶 = 𝛼 ℎ𝜐 𝑏 + 𝑐.
  13. An example of Tauc plot is shown in the Figure

    below, where optical diffuse reflectance data plotted as the indirect bandgap transformation of the Kubelka Munk function for pure ZrNiSn. A linear fit (red dotted line) was used to estimate the band gap by extrapolating to zero absorption, indicating that the band gap is ~0.13 eV. For more details and discussion on bandgap determination see Ref. [8]. Лекция «Введение в физику полупроводников» / 8 августа 2022 г. 15 Optical bandgap: Tauc plot
  14. Лекция «Введение в физику полупроводников» / 8 августа 2022 г.

    16 References 1. Kireev, P.S. Semiconductor Physics, 2nd ed.; Mir: Moscow, 1978. 2. Goldsmid, H.J.; Sharp, J.W. Estimation of the Thermal Band Gap of a Semiconductor from Seebeck Measurements. J. Electron. Mater. 1999, 28 (7), 869–872. 3. Kim, H.-S.; Gibbs, Z.M.; Tang, Y.; Wang, H.; Snyder, G.J. Characterization of Lorenz Number with Seebeck Coefficient Measurement. APL Mater. 2015, 3 (4), 041506. 4. Kasap, S.; Koughia, C.; Ruda, H.E. Electrical Conduction in Metals and Semiconductors. In Springer Handbook of Electronic and Photonic Materials; Springer International Publishing: Cham, 2017; pp 19–45. 5. Wendlandt, W.W.; Hecht, H.G. Reflectance Spectroscopy (Chemical Analysis); Interscience Publishers, 1966. 6. Seeger, K. Semiconductor Physics; Springer Series in Solid-State Sciences; Springer Berlin Heidelberg: Berlin, Heidelberg, 1982. 7. Tauc, J. Optical Properties and Electronic Structure of Amorphous Ge and Si. Mater. Res. Bull. 1968, 3 (1), 37–46. 8. Gibbs, Z.M. PhD thesis: Band Engineering in Thermoelectric Materials Using Optical, Electronic, and Ab-Initio Computed Properties, California Institute of Technology, 2015.