Upgrade to Pro — share decks privately, control downloads, hide ads and more …

Sener Dikmese - Enhanced spectrum sensing techn...

SCEE Team
November 25, 2013

Sener Dikmese - Enhanced spectrum sensing techniques for cognitive radio systems

SCEE Team

November 25, 2013
Tweet

More Decks by SCEE Team

Other Decks in Research

Transcript

  1. ENHANCED SPECTRUM SENSING TECHNIQUES FOR COGNITIVE RADIO SYSTEMS 25.11.2013 Sener

    Dikmese Department of Electronics and Communications Engineering, Tampere University of Technology, Tampere, Finland [email protected]
  2. ¾Part 1 : FFT and Filter Bank Based Spectrum Sensing

    for WLAN Signals ¾Part 2 : Optimized FFT and Filter Bank Based Spectrum Sensing for Bluetooth Signal ¾Part 3 A: FFT and Filter Bank Based Spectrum Sensing and Spectrum Utilization for Cognitive Radio ¾Part III B: Spectrum Sensing And Spectrum Utilization Model For OFDM and FBMC Based Cognitive Radios ¾Part 4 A: Performance Analysis of Eigenvalue Based Spectrum Sensing under Frequency Selective Channels ¾Part 4 B: Reducing Computational Complexity of Eigenvalue Based Spectrum Sensing for Cognitive Radio ¾Part 4 C: Reduced Complexity Spectrum Sensing Based on Maximum Eigenvalue and Energy 27.11.2013 Outline
  3. ¾2.4 GHz ISM Band ¾ Due to the global availability,

    low cost wireless systems use this band ¾ One important problem is interferences to each other ¾Cognitive Radio ¾ Potential solution for interference problem ¾ Spectral holes can be determined robustly ¾Spectrum Sensing ¾ One of the main tasks of a CR for non-interfered spectrum ¾ Different spectrum sensing algorithms can be applied such as blind and non-blind 25.11.2013 INTRODUCTION
  4. ¾ OFDM and Filter Bank Multicarrier (FBMC) ¾ Effects in

    terms of spectrum sensing ¾ FFT and AFB based spectrum sensing ¾ The goal of this paper ¾ Basic spectrum sensing functions for a CR in the ISM band ¾ CP-OFDM based 802.11g WLANs ¾ Most basic spectrum sensing method, energy detection ¾ FFT and AFB in analyzing the radio scene consisting of WLAN signals at different center frequencies 25.11.2013 INTRODUCTION
  5. 25.11.2013 AFB AND FFT BASED ENERGY DETECTOR ALGORITHMS Block diagram

    of energy detector with AFB and FFT based spectrum analysis •The block diagram of alternative FFT and AFB based spectrum sensing algorithms is shown in Figure .
  6. ¾ where is the transmitted signal by primary users as

    it appears at the FFT or AFB output sample in subband , and is the corresponding channel noise sample. and illustrate the absent hypothesis and present hypothesis of a primary user (PU), respectively. ¾ In this study, rectangular ¿lter window is used for its simplicity and lower computational complexity. In this case, the decision statistics at different frequencies can be calculated as 25.11.2013 AFB AND FFT BASED ENERGY DETECTOR ALGORITHMS Typically, the sampling rate of the subbands is equal to the ADC sampling rate divided by the number of channels in filter bank. In the spectrum sensing context, the subband signals can be expressed as 0 1 ( , ) ( , ) ( , ) ( , ) k W m k H Y m k S m k H W m k H ­ ½ ® ¾  ¯ ¿ ( , ) S m k th m k ( , ) W m k 0 H 1 H 2 / 2 1 1 / 2 ( , ) ( , ) f t f k L m u m L l k L Y m k Y u l ª º   « »   « » ¬ ¼ ¦ ¦ 
  7. 25.11.2013 AFB AND FFT BASED ENERGY DETECTOR ALGORITHMS As has

    Gaussian distribution, the decision statistics follows chi-square distribution with degrees of freedom, . Hence, can be modeled as ( ) Y k ( ) Y k  2 f t L L 2 2 2 0 2 2 2 2 1 2 ( ) 2 f t f t w L L w k L L H Y k H k V F V V F N ­ ½ ° ° ° ° ® ¾  ° °  ° ° ¯ ¿  When the signal is present, is considered and thus it can be defined as When the signal is absent and there is only noise, but the decision device decides incorrectly that a signal is present, the false alarm probability is formulated as With the above assumptions, the probabilities and can be written as D P 1 Pr( | ) D P Y H O !  FA P 0 Pr( | ) FA P Y H O !  FA P D P 2 1 ( , ) FA f t w P L L O V  * 2 2 1 ( , ) D f t w k P L L O V V  * 
  8. SIMULATION RESULTS OF FFT AND AFB BASED ENERGY DETECTOR SPECTRUM

    SENSING ALGORITHMS 25.11.2013 Two WLAN signals spectra in 2.4 GHz ISM band. • We can see the ideal OFDM signal spectrum, which has a deep hole in the considered 3 MHz frequency band. •In the worst case situation allowed by the 802.11g specifications, the power spectral density in the gap can be at about -20 dBr (20 dB below the passband level) in the considered case. •Figure shows also a third case with modest spectral regrowth at - 30 dBr level.
  9. SIMULATION RESULTS OF FFT AND AFB BASED ENERGY DETECTOR SPECTRUM

    SENSING ALGORITHMS 25.11.2013 Actual false alarm probability of WLAN signals with target PFA =0.1 for 3 MHz sensing bandwidth in AWGN case. Figure show the actual false alarm probabilities as a function of the active WLAN SNRs for AWGN.
  10. SIMULATION RESULTS OF FFT AND AFB BASED ENERGY DETECTOR SPECTRUM

    SENSING ALGORITHMS 25.11.2013 Actual false alarm probability of WLAN signals with target PFA =0.01 for 3 MHz sensing bandwidth in Rayleigh case. Figure show the actual false alarm probabilities as a function of the active WLAN SNRs for Rayleigh type frequency selective channels.
  11. CONCLUSION ¾FFT or filter band based spectrum analysis methods has

    been studied in this paper. ¾WLAN signals are characterized by rather limited spectral purity, which results in significant interference in the possible spectral gaps between WLAN signals. ¾This leads to obvious hidden node problems when trying to use the WLAN spectral gaps in a well-controlled way for secondary transmissions. ¾With worst-case energy leakage (at about 20 dBr level) of WLAN signals to the spectral gaps, filter bank based spectrum analysis doesn’t provide significant benefits over FFT-based methods. ¾However, already 10 dB reduction in the spectral regrowth level reveals the spectral leakage problems of FFT and AFB methods become clearly better. 25.11.2013
  12. Part 2 : Optimized FFT and Filter Bank Based Spectrum

    Sensing for Bluetooth Signal 25.11.2013
  13. ¾ OFDM Based WLAN and FHSS Based Bluetooth ¾ Bluetooth

    sensing is analyzed also in the presence of WLANs at nearby frequencies. ¾ The goal of this paper ¾ Energy detector based spectrum sensing techniques are optimized for detecting Bluetooth signals, considering both the effect of non-flat power spectrum and frequency hopping characteristics. ¾ To reduce complexity and required number of samples for effective spectrum sensing, optimum weighting process is proposed for subband based spectrum sensing. 25.11.2013 INTRODUCTION
  14. 25.11.2013 OPTIMIZING ENERGY DETECTION FOR NON-FLAT PU SPECTRUM Block diagram

    of energy detector with AFB and FFT based spectrum analysis •The block diagram of alternative FFT and AFB based spectrum sensing algorithms is shown in Figure . •Weight process is applied after the time filtering process to reduce the complexity /required # of samples
  15. 25.11.2013 OPTIMIZING ENERGY DETECTION FOR NON-FLAT PU SPECTRUM 0 1

    ( , ) ( , ) ( , ) ( , ) k W m k H Y m k S m k H W m k H ­ ½ ® ¾  ¯ ¿ 2 1 1 ( , ) f f t f f K L K L L K k k k m k K L k K L t T w T w Y m k L     § · ¨ ¸ © ¹ ¦ ¦ ¦ 0 1 2 4 2 2 2 2 2 1 ( ) ( , ) 1 ( ) ( , ( ) ) k n n H t k k n k n H t f T N L f T N L V V V V V V     0 1 2 2 4 4 2 2 2 4 2 2 2 1 ( ) ( , ) 1 ( ) ( ( ), ( ) ) f f f f f f f f K L K L K k n k n H k K L k K L t K L K L K k k n k k n H k K L k K L t f T N w w L f T N w w L V V V V V V         ¦ ¦   ¦ ¦  
  16. 25.11.2013 OPTIMIZING ENERGY DETECTION FOR NON-FLAT PU SPECTRUM 1 Pr(

    | ) D P T H O ! 0 Pr( | ) FA K P T H O ! 2 2 4 4 ( ) 1 f f f f K L k n k K L FA K L k n k K L t w P Q w L O V V      ¦ ¦ 2 2 2 4 2 2 2 ( ) ( ) 1 ( ) f f f f K L k n k k K L D K L k n k k K L t w P Q w L O V V V V       ¦  ¦ 1 4 4 2 2 1 ( ) f f f f K L K L FA k n k n k K L k K L t Q P w w L O V V       ¦ ¦ 1 4 2 2 2 2 1 ( ) ( (1 )) ( (1 )) f f f f K L K L D k n k k n k k K L k K L t Q P w SNR w SNR L O V V         ¦ ¦ 1 4 4 1 4 2 2 2 2 2 2 [ ( ) ( ) ( (1 )) ] [ ] f f f f f f K L K L FA k n D k n k k K L k K L t K L k n k k K L Q P w Q P w SNR L w SNR V V V           ¦ ¦ ¦ 2 2 2 1 f f k k K L k k K L w V V   ¦
  17. SIMULATION RESULTS OF FFT AND AFB BASED ENERGY DETECTOR SPECTRUM

    SENSING ALGORITHMS 25.11.2013 Bluetooth signal spectrum in 2.4 GHz ISM band • The Frequency Hopped Frequency Shift Keying (FH-FSK) -based 802.15 Bluetooth signal has 79 different frequency channels at center frequencies starting from 2.402 GHz and ending at 2.480 GHz, with 1 MHz spacing. • The nominal bandwidth of BT signal is 1 MHz and the hopping rate is 1600 hops/sec. • We consider first a simplified scheme with continuous BT signal at the 33nd channel.
  18. SIMULATION RESULTS OF FFT AND AFB BASED ENERGY DETECTOR SPECTRUM

    SENSING ALGORITHMS 25.11.2013 Required time record length in different weighting schemes • We can see that almost the same time record length can be used when sensing a single subband at the BT center frequency as when sensing the whole 1 MHz BT band. • With constant weights, 3 subbands is the optimum choice in all these cases. •Using optimum weights, the sensing time can be reduced by about 10 %, and most of this benefit is gained by using only 5 subbands. Bluetooth SNR Weight Factors 11 subbands 5 subbands 3 subbands 1 subband 0 dB Const. 12 8 8 15 Opt. 7 7 8 -3dB Const. 39 25 23 41 Opt. 21 21 23 -4 dB Const. 60 37 34 60 Opt. 31 31 33 -5 dB Const. 92 56 51 89 Opt. 45 46 49 -6 dB Const. 143 84 77 132 Opt. 68 69 73 -7 dB Const. 223 131 117 200 Opt. 104 105 111
  19. SIMULATION RESULTS OF FFT AND AFB BASED ENERGY DETECTOR SPECTRUM

    SENSING ALGORITHMS 25.11.2013 Two WLAN channels and Bluetooth signal spectra in 2.4 GHz ISM band. (a) WLAN channels 3 and 8, (b) WLAN channels 3 and 7. • In the worst case situation allowed by the 802.11g specifications, the power spectral density in the 3 MHz gap can be at about -20 dBr (20 dB below the passband level) in the considered case. • The figure shows also a third case with modest spectral regrowth at - 30 dBr level. • In the ‘no gap’ case, there isn’t really any spectral hole.
  20. SIMULATION RESULTS OF FFT AND AFB BASED ENERGY DETECTOR SPECTRUM

    SENSING ALGORITHMS 25.11.2013 ROC curves in Bluetooth sensing with time record length of 50 samples for constant weights (upper) and optimized weights (lower). Analytic and FFT models in AWGN case with -5 dB SNR. • In these simulation models, the time record length is chosen as 50 samples, due to the hopping limit corresponding to approximately 625 ȝs. •The simulated performance is slightly worse than the analytical model. •To compensate the difference, the time record length should be increased by about 10 %. •But we are still able to reach false alarm and detection probabilities of 0.1 and 0.9 at -5 dB SNR with 50 samples.
  21. SIMULATION RESULTS OF FFT AND AFB BASED ENERGY DETECTOR SPECTRUM

    SENSING ALGORITHMS 25.11.2013 Actual false alarm probability for BT signals with target SNR of -5 dB and PFA =0.1 using optimum weight values under AWGN case. (a) BT frequency closest to WLAN. (b) BT frequency at the center between channels 3 and 7. (c) BT frequency at the center of 3 MHz gap. • The constant weight case uses 3 subbands, which provides the best detection probability performance. •With optimum weight values using 11 subbands, highest detection probability performance is achieved again, but the benefit over the constat weight case is marginal. In this low dynamic range case, there is no big difference in detection probability between FFT and AFB.
  22. SIMULATION RESULTS OF FFT AND AFB BASED ENERGY DETECTOR SPECTRUM

    SENSING ALGORITHMS 25.11.2013 Detection probability of Bluetooth signal with target PFA =0.1 using time record length of 50 for constant and optimum weight values in AWGN. • First a BT channel at the nominal band edge, which includes strong side lobes of the WLAN signal, is investigate in figure 6(a). •In figure 6(b), the BT in the center frequency between two WLAN signals at channels 3 and 7 is considered to see the effect of spectral leakage. •Figure 6(c) shows the corresponding case for 3 MHz gap between WLANs at chennels 3 and 8.
  23. CONCLUSION ¾We have analyzed the performance of energy detection based

    spectrum sensing techniques with weight process utilizing either FFT or filter bank based spectrum analysis methods. ¾Moving average processing is an efficient way to align the sensing time interval with the transmission burst. ¾Use of weighting process provides somewhat better performance compared to constant weights. ¾If weighting is not used, it is very important to select the number subbands optimally. ¾While there is no big difference between FFT and AFB based spectrum sensing with small spectral dynamic range, the AFB based algorithm has clearly better performance in identifying spectral holes between spectrally well-contained PU signals. ¾In the neighborhood of 802.11 WLAN channels, energy detection based spectrum sensing performance depends greatly on the level of spectral regrowth due to WLAN power amplifier nonlinearity. 25.11.2013
  24. Part 3 A: FFT and Filter Bank Based Spectrum Sensing

    and Spectrum Utilization for Cognitive Radio 25.11.2013
  25. 25.11.2013 AFB & FFT Based Spectrum Sensing Algorithms Block diagram

    of energy detector with AFB and FFT based spectrum analysis •. In the following analysis, it is assumed that the subband sampling rate is equal to the ADC sampling rate divided by the number of FFT/AFB frequency bins.
  26. 25.11.2013 AFB & FFT Based Spectrum Sensing Algorithms 0 1

    ( , ) ( , ) ( , ) ( , ) k W m k H Y m k S m k H W m k H ­ ½ ® ¾  ¯ ¿ 2 /2 1 1 /2 1 ( , ) ( , ) f t f k L m u m L l k L t f Y m k Y u l L L ª º   « »   « » ¬ ¼ ¦ ¦  0 1 2 4 2 2 2 2 2 1 ( ) ( , ) 1 ( ) ( , ( ) ) K n n H t f K k n k n H t f f Y N L L f Y N L L V V V V V V       1 4 2 ( ) / FA n t f n Q P L L O V V   2 2 1 2 2 2 ( ) Pr( | ) ( ) ( ) / n k D K n k t f P Y H Q L L O V V O V V   !   2 0 4 Pr( | ) ( ) / n FA K n t f P Y H Q L L O V O V  ! 
  27. 25.11.2013 SPECTRUM UTILIZATION Block diagram of spectrum utilization with water

    filling algorithm after spectrum analysis •Here the rate adaptive loading algorithm is considered as it provides better control of the interference from a CR to the PU receivers.
  28. 25.11.2013 SPECTRUM UTILIZATION 2 1 1 * 1 log 2

    N n n n e g b = æ ö + ÷ ç ÷ = ç ÷ ç ÷ ç G è ø å 2 1 1 1 * 1 max log 2 : = = æ ö + ÷ ç ÷ = ç ÷ ç ÷ ç G è ø = å å n N n n e n N x n n e g b subject to Ne e 1 1 1 N i n n n K Ne N i g - = é ù ê ú = +G× ê ú - ê ú ë û å / 0 i i e K g = -G £ / n n e K g = -G * 2 log (1 )/ 2 1,2, , n n n b e g n N = + × " = "
  29. SIMULATION RESULTS OF FFT AND AFB BASED ENERGY DETECTOR SPECTRUM

    SENSING ALGORITHMS 25.11.2013 Two WLAN signal spectra in 2.4 GHz ISM band. (a) WLAN channels 3 and 8, (b) WLAN channels 3 and 7. • In the first case WLAN1 and WLAN2 signals use channels 3 and 8, respectively, out of the entire 11 different channels. • For the second case, WLAN1 and WLAN2 occupy channels 3 and 7, respectively. •The channels don't overlap and there are 8 MHz and 3 MHz spectrum holes available in the two cases, respectively. •According to the 802.11g based WLAN signal properties, energy leakage can still be expected to these bands, since the allowed relative spectrum densities are 20 ... 25 dB below the signal passband level.
  30. SIMULATION RESULTS OF SPECTRUM SENSING ALGORITHMS 25.11.2013 •Figure 1 shows

    this effect in terms of the number of subbands determined to be empty depending on the WLAN SNR. •Two WLANs are assumed to have the same power level, normalized to 0 dB and the target false alarm probability is chosen as 0.1. •Similiar results are valid for the bandwidth of spectral hole, as seen in figure 2.
  31. SIMULATION RESULTS OF SPECTRUM SENSING ALGORITHMS 25.11.2013 • The results

    are given for groups of 5 subbands in the center of the spectral hole and right next to the guardbands. •In the latter case, the spectrum leakage of the WLAN signal degrades the sensing performance already with low WLAN SNRs. In the center of the 3 MHz or 8 MHz spectral hole, the leakage is not significant. •However, the poor frequency selectivity of plain FFT based processing degrades the performance of FFT based sensing with modest and high SNRs, whereas the AFB has clearly better performance.
  32. SIMULATION RESULTS OF SPECTRUM SENSING ALGORITHMS 25.11.2013 • The utilization

    of the 3 MHz and 8 MHz white spaces between the active WLANs with the rate adaptive algorithm is shown in figure 7. •Constant 10 dB SNR is used for the CR. The channel estimation is assumed to be perfect and the subband wise noise + interference power estimates are obtained using time filtering length of 50.
  33. SIMULATION RESULTS OF SPECTRUM SENSING ALGORITHMS 25.11.2013 • Finally, figure

    8 shows the achievable data rate in the spectrum gap between two active WLANs, as determined by the rate adaptive algorithm. •Naturally, the number of bits for each subband, has been rounded to the nearest integer value.
  34. CONCLUSION 25.11.2013 • We have analyzed the performance of energy

    detection based spectrum sensing techniques using either FFT or filter bank based spectrum analysis methods and utilizing spectral holes with water filling algorithms. • Due to low leakage, the AFB spectrum analysis based algorithm has clearly better performance in identifying spectral holes between spectrally well-contained PUs. • The same is true regarding the noise + interference power estimation needed for rate adaptive bit loading. • In the neighborhood of WLAN channels, energy detection based spectrum sensing performance depends greatly on the level of spectral regrowth due to WLAN power amplifier nonlinearity. • However, analyzing this effect in the spectrum exploitation context is left as a topic for future studies.
  35. Part 3 B: Spectrum Sensing And Spectrum Utilization Model For

    OFDM and FBMC Based Cognitive Radios 25.11.2013
  36. ¾ Spectrum sensing is a vital part of short-range CR

    applications. ¾ CRs may sense the local spectrum through dedicated sensors, or the spectrum sensing function can be closely integrated with the receiver RF and signal processing modules of access points and mobile stations. ¾ After the spectrum is sensed, efficient spectrum utilization becomes important. Multicarrier techniques provide a solution for efficient transmission of data over channel with frequency selective fading. ¾ When the Channel State Information (CSI) is known, the transmit power or the data rate can be adapted according to the CSI. ¾ The adaptation algorithms, the so-called called loading algorithms use commonly the water-filling principle. Water-filling solution can be thought of as the curve of inverted channel signal to noise ratio being filled with energy to a constant line. 25.11.2013 INTRODUCTION
  37. SIMULATION RESULTS OF FFT AND AFB BASED ENERGY DETECTOR SPECTRUM

    SENSING ALGORITHMS 25.11.2013 Two WLAN and FBMC signals using 3rd and 8th WLAN channels in 2.4 GHz ISM band.
  38. SIMULATION RESULTS OF SPECTRUM SENSING ALGORITHMS 25.11.2013 • As we

    can see, with no or modest spactral regrowth, an FBMC primary would allow a clearly higher number of subchannels to be used by the CR system compared to OFDM- based WLAN. Also AFB finds higher number of empty subbands compared to FFT, in reliable way. With the worst-case regrowth allowed by 802.11g, the differences dissappear.
  39. SIMULATION RESULTS OF SPECTRUM SENSING ALGORITHMS 25.11.2013 •The actual false

    alarm probabilities versus the active primary systems’ SNR, as seen by the CR receiver, can be seen in figure 5. •This is actually the probability that a group of 5 subchannels in the center of the gap would be detected to be occupied due to spectral leakage.
  40. SIMULATION RESULTS OF SPECTRUM SENSING ALGORITHMS 25.11.2013 • Finally, the

    achievable data rate in the spectrum gap between two active primary channels, as determined by the rate adaptive algorithm, are shown in figure. •Perfect channel estimation is assumed and the subband-wise SINR (signal to interference plus noise ratio) estimates are obtained using time filtering length of 50 samples.
  41. CONCLUSION 25.11.2013 • We have analyzed the performance of energy

    detection based spectrum sensing techniques using either FFT or filter bank based spectrum analysis methods for both WLAN and FBMC signal models and utilizing spectral holes with water filling algorithms. • As a spectrum sensing method, AFB has clear benefits due to much better spectral containment of the sub channels. • One significant benefit of FBMC as a transmission technique in CR systems is that it can utilize narrow spectral gaps in an effective and flexible way. • On the other hand, FBMC multicarrier eliminates the extra complexity due to AFB design because of its transmitter and receiver characteristics. • As a conclusion, use of FBMC model, instead of OFDM based WLAN model provides better performance in terms of the spectral leakage problem.
  42. ¾ There are many problems which effect the performance of

    spectrum sensing in practice. ¾ The first problem is that reliable sensing has to be achieved with very low signal- to-noise ratio (SNR). ¾ Secondly, the multipath fading and shadowing cause power fluctuation of the received signal .Variation and unpredictability of the precise noise level at the sensing device is another critical issue, which is called “noise uncertainty”. ¾ Especially, the performance of the traditional energy detector based spectrum sensing methods significantly decreases under noise uncertainty 25.11.2013 INTRODUCTION
  43. ¾ The goal of this paper is to investigate the

    effects of frequency selective channel, considering also the noise uncertainty effects, using traditional energy detector and eigenvalue based spectrum sensing. ¾ We consider a simplified signal scenario, where only Gaussian signal model is used under INDOOR, SUI-1 and ITU-R Vehicular A multipath delay profiles ¾ The applications of cooperative sensing approaches are left as topics for future studies. 25.11.2013 INTRODUCTION
  44. 25.11.2013 SPECTRUM SENSING TECHNIQUES A) Energy detector based spectrum sensing

    with noise uncertainty 2 1 0 1 [ ] N y n T y n N  ¦ 2 4 0 2 2 2 2 2 1 1 ( , ) 1 ( , ( ) ) y w w H y x w x w H T N N T N N V V V V V V     1 ( | ) D y P P T H J ! 0 ( | ) FA y P P T H J ! 1 4 2 1 ( ) FA w w Q P N J V V   2 4 0 1 ( | ) (( )/ ) FA y w w P P T H Q N J J V V !  2 2 1 2 2 2 ( ) ( | ) ( ) 1 ( ) x w D y x w P P T H Q N J V V J V V   !  2 2 2 2 2 2 1 , 2 2 2 1 (( )/ ( ) ) max 1 (( ) / ( ) ) w w FA w w P Q N Q N V V UV U J V V J UV UV ª º « » ¬ ¼   2 2 2 2 2 2 2 2 1 , 2 2 2 2 2 1 (( ( ))/ ( ) ) min ( (1/ ) ) ( ) 1 ( (1/ ) ) w w D x x x w x w P Q N Q N V V UV U J V V V V J V U V V U V ª º « » ¬ ¼       2 2 2 [(1/ ) , ] w w V U V UV  2 ( ) 2 2 0 : ( ) ( ) (0, ) 1: ( ) ( ) ( ) ( ) (0, ) w x n x w H y n w n N H y n s n c n w n N V V V …      
  45. 25.11.2013 SPECTRUM SENSING TECHNIQUES B) Eigenvalue Based Spectrum Sensing under

    different frequency selective channel cases 2 ( ) 2 2 0 : ( ) ( ) (0, ) 1: ( ) ( ) ( ) (0, ) w X n x w H y n w n N H y n s n ch w n N V V V …       † † † † ˆ ˆ ( ) ˆˆ ( ) ˆ ˆ ( ) yy ss ww yy ss ww E E E  R yy R ss R ww R HR H R Algorithm 1 Algorithm 2 max min 1 ( / ) O O J ! 1 2 0 1 ( ) ( ) NM n T N y n MN  ¦ min 2 ( ( )/ ) T N O J ! ˆ [ ( ) ( 1) ( 2)... ( 1)] , ˆ [ ( ) ( 1) ( 2)... ( 1)] , ˆ [ ( ) ( 1) ( 2)... ( 1)] T T T y n y n y n y n ML s n s n s n s n ML w n w n w n w n ML             y s w 2 † 1 1 ˆ ˆ ( ) ( ) ( ) L N yy n ML N n n N    ¦ R y y 2 † 1 1 ˆ ˆ ( ) ( ) ( ) L N ww n ML N n n N    ¦ R w w 2 2/ 3 1 1 1/ 6 2 ( ) ( ) . 1 (1 ) ( ) ( ) FA N ML N ML F P NML N ML J   § ·     ¨ ¸ ¨ ¸  © ¹ 1 2 2 1 ( ) 1 ( ) FA N Q P MN N ML J  § ·  ¨ ¸ ¨ ¸  © ¹
  46. SIMULATION RESULTS OF FFT AND AFB BASED ENERGY DETECTOR SPECTRUM

    SENSING ALGORITHMS 25.11.2013 Examples non-oversampled and 2x-oversampled spectral models under Vehicular A channel and AWGN noise. • Simple Gaussian signal models which includes both non- oversampled and 2x-oversampled signal are shown as seen figure 1. • In this figure, the signals are shown for the ITU-R Vehicular A channel case [11]. •In our signal model, the bandwidth is chosen as 20 MHz. The Vehicular A channel model has 6 taps the maximum delay spreads is about 2.5 ms.
  47. SIMULATION RESULTS OF SPECTRUM SENSING ALGORITHMS 25.11.2013 • Figures show

    detection probabilities of traditional energy detector and eigenvalue based spectrum sensing under INDOOR channel. •1 dB noise uncertainty is chosen to see the performance of detection probabilities for 10000 numbers of samples.
  48. SIMULATION RESULTS OF SPECTRUM SENSING ALGORITHMS 25.11.2013 • Figures show

    detection probabilities of traditional energy detector and eigenvalue based spectrum sensing under Vehicular channel. •1 dB noise uncertainty is chosen to see the performance of detection probabilities for 10000 numbers of samples.
  49. SIMULATION RESULTS OF SPECTRUM SENSING ALGORITHMS 25.11.2013 • Figures show

    detection probabilities of traditional energy detector and eigenvalue based spectrum sensing under SUI channel. •1 dB noise uncertainty is chosen to see the performance of detection probabilities for 10000 numbers of samples.
  50. SIMULATION RESULTS OF SPECTRUM SENSING ALGORITHMS 25.11.2013 • Figures show

    detection probabilities of traditional energy detector and eigenvalue based spectrum sensing under SUI channel. •1 dB noise uncertainty is chosen to see the performance of detection probabilities for 10000 numbers of samples.
  51. CONCLUSION ¾We have analyzed the performance of the traditional energy

    detector and eigenvalue based spectrum sensing techniques under different frequency selective channels, the Indoor, ITU-R Vehicular A and SUI-1 channel models in particular. • It was seen that max/min eigenvalue approach gives consistently better detection performance that energy/min eigenvalue approach. Especially, in simulation based results with oversampling the difference is significant. ¾We have seen that eigenvalue based spectrum sensing clearly exceeds the performance of energy detector with 1 dB noise uncertainty with Indoor and Vehicular-A channel models, whereas with SUI-1, the difference is rather small. ¾Using oversampled signal model in detection clearly reduces the false alarm probability with eigenvalue based sensing. 25.11.2013
  52. CONCLUSION 25.11.2013 ¾One related general aspect regarding spectrum sensing is

    the following: When the sensing station has a line-of sight (LOS) connection, the channel can be expected to be mildly frequency selective, but also the power level is high due to lower path loss. ¾When the sensing station does not have a LOS connection, the signal level is lower, but also the channel can be expected to be highly frequency selective. ¾Thus, in case of shadowing, the PU signal can be detected using the eigenvalue based approach without essential limitations due to noise uncertainty. In case of LOS channel, simple energy detection based approach might be sufficient.
  53. INTRODUCTION 56 25.11.2013 ¾ Spectrum sensing of primary users under

    very low signal-to-noise ratio (SNR) and noise uncertainty is crucial for cognitive radio (CR) systems. ¾ To overcome the drawbacks of weak signal and noise uncertainty, eigenvalue-based spectrum sensing methods have been proposed for advanced CRs. ¾ However, one pressing disadvantage of eigenvalue-based spectrum sensing algorithms is their high computational complexity, which is due to the calculation of the covariance matrix and its eigenvalues. ¾ In this study, power, inverse power and fast Cholesky methods for eigenvalue computation are investigated as potential methods for reducing the computational complexity.
  54. TRADITIONAL EIGENVALUE-BASED SPECTRUM SENSING 57 25.11.2013 Algorithm 1: Max-Min eigenvalue

    based sensing (MME) 2 0 ( ) 2 2 1 : ( ) ( ) (0, ) : ( ) ( ) ( ) ( ) (0, ) w x n x w H y n w n N H y n s n h n w n N V V V | …  |    † † † ˆˆ ˆ ˆ ˆ ˆ ( ); ( ); ( ) yy ss ww E E E R yy R ss R ww † y y c s s c w w  R H R H R Algorithm 2: Energy with min eigenvalue based sensing (EME) 2 † 1 1 ˆ ˆ ( ) ( ) ( ) L N yy n ML N n n N    ¦ R y y 2 2/3 1 1 1 1/6 2 ( ) ( ) . 1 (1 ) ( ) ( ) FA N ML N ML F P NML N ML J   § ·     ¨ ¸ ¨ ¸  © ¹ When , the primary signal is assumed to be present, otherwise it is assumed that there is no transmitted signal in the band of interest at this time. max min 1 ( / ) O O J ! 1 2 0 1 ( ) ( ) NM n T N y n MN  ¦ 1 2 2 1 ( ) 1 ( ) FA N Q P MN N ML J  § ·  ¨ ¸ ¨ ¸  © ¹ When , the signal is assumed to be present, otherwise it is expected that there is only noise in the band of interest. min 2 ( ( )/ ) T N O J !
  55. PROPOSED EIGENVALUE BASED ALGORITHMS 58 25.11.2013 The Power Method to

    find the largest eigenvalue The Inverse Power Method to find the smallest eigenvalue Input: yy R , the matrix; 0 v , an initial guess of an eigenvector such that 0 v = 1 For k = 1, 2, 3, …, do 1 yy k m w R v k m v w w † k k yy k O mv R v End for Output: k O , the approximation of the maximum eigenvalue of yy R after the th k iteration. The power method is an iterative algorithm which approximates the largest dominant eigenvalue of a symmetric positive definite matrix in operations, where is the number of iterations under a certain error threshold. ( ) O kML k The inverse power method is an iterative algorithm which approximates the smallest eigenvalue, without finding and sorting all eigenvalues. Theorem 1: Let be a non-singular matrix i.e. are non-zero for all , then has eigenvalues for all yy R m m u 1 i m d d 1 yy  R 1/ i O 1 i m d d Proof: is non-singular, there exists and there exists such that  yy R 0 i O z 0 x z 1 1 1 1 ( ) 1 yy i yy yy yy i I yy i O O O    Ÿ Ÿ R x x R R x R x x R x 
  56. FAST CHOLESKY FACTORIZATION OF TOEPLITZ MATRIX 59 25.11.2013 ¾ The

    inverse power method is therefore applying the power method on the inverse of the matrix for approximating the smallest dominant eigenvalue. ¾ However, computing explicitly is numerically expensive and unstable, and generally takes operations using naive Gaussian elimination. ¾ A common implementation of the inverse power iteration uses LU decomposition, which has a lower complexity of . ¾ Hence, the overall computational complexity of the inverse power method is , as the complexity of LU factorization dominates. ¾ To reduce the complexity of the calculations, well known traditional iterative Schur algorithm is proposed in this study. ¾ Computational complexity can be decreased as with iterative Schur algorithm. 1 R yy  4 4 ( ) O M L 3 3 (4 / 3 ) O M L 3 3 ( ) O M L 2 2 ( ) O M L
  57. SIMULATIONS AND NUMERICAL RESULTS 60 25.11.2013 Simulation Parameters: • Number

    of samples : •Smoothing factor : •The bandwidth : 20 Mhz • Max delay spread : • The number of ite. : k=100 Difference of computed smallest eigenvalue using Schur or Cholesky based inverse power methods in comparison with eigen-decomposition method, for varying matrix dimension under different SNR cases. 10000 N = 16 L = 2.5 s m
  58. SIMULATIONS AND NUMERICAL RESULTS 61 25.11.2013 Simulated detection probabilities using

    traditional and proposed eigenvalue-based spectrum sensing algorithms with (non-oversampled), and Indoor channel. Theoretical performance of energy detector without noise uncertainty and with 1 dB noise uncertainty included as reference. 1 M 16 L Simulated detection probabilities using traditional and proposed eigenvalue-based spectrum sensing algorithms with (4x-oversampled), and ITUR-A vehicular channel. Theoretical performance of energy detector without noise uncertainty and with 1 dB noise uncertainty included as reference. 4 M 16 L
  59. SIMULATIONS AND NUMERICAL RESULTS 62 25.11.2013 ALGORITHMS Cov. Matrix Eigen.

    Decom. Ave. Test Stat. Total max min Trad. Alg. Alg. 1 (max. eig. / min. eig.) MLN 3 3 ( ) O M L 3 3 ( ) MLN O M L + Alg. 2 (average / min. eig.) MLN 3 3 ( ) O M L MN 3 3 ( ) M LN OM L M N + + Prop. Alg. Alg. 1 (max. eig. / min. eig.) Cholesky factorization MLN ( ) O kML 3 3 ( /3) OM L - 3 3 ( ) ( / 3) MLN O kML O M L + + Schur Algorithm 2 2 ( ) OM L 2 2 ( ) ( ) MLN O kML O M L + + Alg. 2 (average / min. eig.) Cholesky factorization MLN - 3 3 ( /3) OM L MN 3 3 ( /3) M LN OM L M N + + Schur Algorithm 2 2 ( ) OM L 2 2 ( ) MLN O M L MN + + COMPUTATIONAL COMPLEXITY OF POWER ITERATION BASED SPECTRUM SENSING
  60. SIMULATIONS AND NUMERICAL RESULTS 63 25.11.2013 ALGORITHMS Smoothing Factor (L)

    Number of samples (N) 103 5x103 104 2x104 Trad. Alg. Alg. 1 (max. eig. / min. eig.) 8 8 512 40 512 80 512 160 512 16 20 096 84 096 164 096 324 096 Alg. 2 (average / min. eig.) 8 9 512 45 512 90 512 180 512 16 21 096 89 096 174 096 344 096 Prop. Alg. Alg. 1 (max. eig. / min. eig.) Cholesky 8 8 971 40 971 80 971 160 970 16 18 965 82 965 162 970 321 856 Schur 8 8 864 40 864 80 864 160 864 16 17 856 81 856 161 856 321 856 Alg. 2 (average / min. eig.) Cholesky 8 9 171 45 171 90 171 180 170 16 18 365 86 365 171 370 341 370 Schur 8 9 064 45 064 90 064 180 064 16 17 256 85 256 170 256 340 256 SOME NUMERICAL VALUES OF COMPUTATIONAL COMPLEXITIES FOR SENSING METHODS (M=1, NON- OVERSAMPLED) Alg. 1 Alg.2
  61. SIMULATIONS AND NUMERICAL RESULTS 64 25.11.2013 SOME NUMERICAL VALUES OF

    COMPUTATIONAL COMPLEXITIES FOR SENSING METHODS (M=2X-OVERSAMPLED) ALGORITHMS Smoothing Factor (L) Number of samples (N) 103 5x103 104 2x104 Trad. Alg. Alg. 1 (max. eig. / min. eig.) 8 20 096 40 512 164 096 324 096 16 64 768 84 096 352 768 672 768 Alg. 2 (average / min. eig.) 8 22 096 45 512 184 096 364 096 16 66 768 89 096 372 768 712 768 Prop. Alg. Alg. 1 (max. eig. / min. eig.) Cholesky 8 18 965 40 971 162 970 322 970 16 46 123 82 965 334 120 654 120 Schur 8 17 856 40 864 161 856 321 856 16 36 224 81 856 324 224 644 224 Alg. 2 (average / min. eig.) Cholesky 8 19 365 45 171 181 370 361 370 16 44 923 86 365 350 920 690 920 Schur 8 18 256 45 064 180 256 321 856 16 35 024 85 256 341 024 681 024 Alg. 1 Alg.2
  62. SIMULATIONS AND NUMERICAL RESULTS 65 25.11.2013 SOME NUMERICAL VALUES OF

    COMPUTATIONAL COMPLEXITIES FOR SENSING METHODS (M=4X-OVERSAMPLED) ALGORITHMS Smoothing Factor (L) Number of samples 103 5x103 104 2x104 Trad. Alg. Alg. 1 (max. eig. / min. eig.) 8 64 768 84 096 352 768 672 768 16 326 144 192 768 902 144 1 542 144 Alg. 2 (average / min. eig.) 8 68 768 94 096 392 768 752 768 16 330 144 202 768 942 144 1 622 144 Prop. Alg. Alg. 1 (max. eig. / min. eig.) Cholesky 8 46 123 82 965 334 120 654 120 16 157 780 174 120 733 780 1 373 800 Schur 8 36 224 81 856 324 224 644 224 16 74 496 164 224 650 496 1 290 496 Alg. 2 (average / min. eig.) Cholesky 8 46 923 91 365 370 920 730 920 16 155 380 180 920 767 380 1 447 400 Schur 8 37 024 90 256 361 024 721 024 16 72 096 171 024 684 096 1 364 096 Alg. 1 Alg.2
  63. CONCLUSION 66 25.11.2013 ¾ An improvement to the computational complexity

    of eigenvalue-based spectrum sensing has been presented in this paper, based on the simple power iteration and inverse power iteration using the Schur algorithm. ¾ In general, the max/min eigenvalue method provides consistently better performance/complexity tradeoff than the energy with min eigenvalue method. ¾ On the other hand, the Schur algorithm has in many cases significanlty lower complexity than the Cholesky approach. ¾ When the number of samples is 1000 with 4x-oversampling, the overall computational complexity (multiplication and addition) of the traditional algorithm 1 is 326144 whereas it is 74496 Schur algorithm. Hence upon using the Schur algorithm, the complexity is reduced by about 80 percent. ¾ Besides numerical algorithms, other aspects of cognitive radio, such a cooperative sensing will also be investigated to reduce the computational complexity as a future work.
  64. INTRODUCTION 68 25.11.2013 ¾ Spectrum sensing of primary users under

    very low signal-to-noise ratio (SNR) and noise uncertainty is crucial for cognitive radio (CR) systems. ¾ Eigenvalue-based spectrum sensing methods have been proposed for advanced cognitive radios to solve the low SNR and noise uncertainty challenges. ¾ One very crucial drawback of eigenvalue based spectrum sensing techniques is their high computation complexity. ¾ In this paper, power methods for eigenvalue computation are studied with the proposed energy with maximum eigenvalue (EMaxE) detection as potential methods for reduced complexity.
  65. TRADITIONAL EIGENVALUE-BASED SPECTRUM SENSING 69 25.11.2013 Algorithm 1: Max-Min eigenvalue

    based sensing (MME) 2 0 ( ) 2 2 1 : ( ) ( ) (0, ) : ( ) ( ) ( ) ( ) (0, ) w x n x w H y n w n N H y n s n h n w n N V V V | …  |    † † † ˆˆ ˆ ˆ ˆ ˆ ( ); ( ); ( ) yy ss ww E E E R yy R ss R ww † y y c s s c w w  R H R H R Algorithm 2: Energy with min eigenvalue based sensing (EME) 2 † 1 1 ˆ ˆ ( ) ( ) ( ) L N yy n ML N n n N    ¦ R y y 2 2/3 1 1 1 1/6 2 ( ) ( ) . 1 (1 ) ( ) ( ) FA N ML N ML F P NML N ML J   § ·     ¨ ¸ ¨ ¸  © ¹ When , the primary signal is assumed to be present, otherwise it is assumed that there is no transmitted signal in the band of interest at this time. max min 1 ( / ) O O J ! 1 2 0 1 ( ) ( ) NM n T N y n MN  ¦ 1 2 2 1 ( ) 1 ( ) FA N Q P MN N ML J  § ·  ¨ ¸ ¨ ¸  © ¹ When , the signal is assumed to be present, otherwise it is expected that there is only noise in the band of interest. min 2 ( ( )/ ) T N O J !
  66. PROPOSED EIGENVALUE BASED ALGORITHMS 70 25.11.2013 The Power Method to

    find the largest eigenvalue The power method is an iterative algorithm which approximates the largest dominant eigenvalue of a symmetric positive definite matrix in operations, where is the number of iterations under a certain error threshold. ( ) O kML k Energy with max eigenvalue based sensing (EmaxE) The threshold value can be calculated using the random matrix theorem. The probability of false alarm of the EmaxE detection can be expressed as J max ( ( )) FA P P T N O J ! max 2 ( ( ( )) ( ) ) w N P A N T N O J V ! 2 max ( ( )) ( ) / ( ) w A N T N N P O P J V P Q Q   ! 1/3 1 1 (1 ) FA ML N N ML F P N ML MLN N J  ª º § ·  « »     ¨ ¸ ¨ ¸ « » © ¹ ¬ ¼ When , the signal is assumed to be present, otherwise it is expected that there is only noise in the band of interest. This algorithm is very robust against noise uncertainty because it doesn’t need knowledge about noise variance. max ( / ( )) T N O J !
  67. SIMULATIONS AND NUMERICAL RESULTS 71 25.11.2013 Some Simulation Parameters: •

    Number of samples : • Smoothing factor : • The bandwidth : • Max delay spread : • The number of ite. : 1000 N = 16 L = 2.5 s m The detection probabilities of simple energy detector, as well as traditional and proposed eigenvalue based spectrum sensing methods have been evaluated using three different channel models (i.e., Indoor, ITU-R Vehicular A and SUI-1 channels). The dB noise uncertainty case is considered as the worst-case scenario in terms of noise variance estimation. The Vehicular A channel has 6 taps and its maximum delay spreads is about 2.5ȝs. 16-tap model with 80 ns rms delay spread is also applied for realistic Indoor channel model as second channel model. SUI-1 channel model which has 3 Ricean fading taps and 0.9 delay spread is used as third channel model. 20 M H z 100 k =
  68. SIMULATIONS AND NUMERICAL RESULTS 72 25.11.2013 Simulated detection probabilities using

    traditional and proposed eigenvalue-based spectrum sensing algorithms with (non-oversampled), and Indoor channel. Theoretical performance of energy detector without noise uncertainty and with 1 dB noise uncertainty included as reference. 1 M 16 L Simulated detection probabilities using traditional and proposed eigenvalue-based spectrum sensing algorithms with (4x-oversampled), and Indoor channel. Theoretical performance of energy detector without noise uncertainty and with 1 dB noise uncertainty included as reference. 4 M 16 L
  69. SIMULATIONS AND NUMERICAL RESULTS 73 25.11.2013 Simulated detection probabilities using

    traditional and proposed eigenvalue-based spectrum sensing algorithms with (non-oversampled), and ITUR-A vehicular channel. Theoretical performance of energy detector without noise uncertainty and with 1 dB noise uncertainty included as reference. 1 M 16 L Simulated detection probabilities using traditional and proposed eigenvalue-based spectrum sensing algorithms with (4x-oversampled), and ITUR-A vehicular channel. Theoretical performance of energy detector without noise uncertainty and with 1 dB noise uncertainty included as reference. 4 M 16 L
  70. SIMULATIONS AND NUMERICAL RESULTS 74 25.11.2013 Simulated detection probabilities using

    traditional and proposed eigenvalue-based spectrum sensing algorithms with (non-oversampled), and SUI-1 channel. Theoretical performance of energy detector without noise uncertainty and with 1 dB noise uncertainty included as reference. 1 M 16 L Simulated detection probabilities using traditional and proposed eigenvalue-based spectrum sensing algorithms with (4x-oversampled), and SUI-1 channel. Theoretical performance of energy detector without noise uncertainty and with 1 dB noise uncertainty included as reference. 4 M 16 L
  71. SIMULATIONS AND NUMERICAL RESULTS 75 25.11.2013 Actual false alarm probability

    of traditional and proposed eigenvalue based spectrum sensing algorithms with (non-oversampled) and oversampling by , and Indoor channel. 1 M 16 L 4 M False alarm probability is not changing with SNR as expected. While the actual false alarm probabilities under the oversampled signal models are very small, the detection probabilities of proposed eigenvalue based spectrum sensing is clearly better compared to the traditional eigenvalue based methods.
  72. SIMULATIONS AND NUMERICAL RESULTS 76 25.11.2013 COMPUTATIONAL COMPLEXITY OF POWER

    ITERATION BASED SPECTRUM SENSING ALGORITHMS Cov. Matrix Eigen. Decom. Ave. Test Stat. Total max min Trad. Alg. Alg. 1 (max. eig. / min. eig.) MLN 3 3 ( ) O M L 3 3 ( ) MLN O M L + Alg. 2 (average / min. eig.) MLN 3 3 ( ) O M L MN 3 3 ( ) M LN OM L M N + + Prop. Alg. EmaxE (max. eig. /average) MLN ( ) O kML - MN ( ) MLN O kML MN   TABLE shows expressions for the computational complexities of traditional methods (based on finding all the eigenvalues) and the proposed eigenvalue based spectrum sensing technique using the max eigenvalue over energy criterion together with power iteration. Here the metric for computational complexity is the overall number of multiplications and additions.
  73. SIMULATIONS AND NUMERICAL RESULTS 77 25.11.2013 SOME NUMERICAL VALUES OF

    COMPUTATIONAL COMPLEXITIES FOR SENSING METHODS (M=1, NON- OVERSAMPLED) ALGORITHMS Smoothing Factor (L) Number of samples (N) 103 5x103 104 2x104 Trad. Alg. Alg. 1 (max. eig. / min. eig.) 8 8 512 40 512 80 512 160 512 16 20 096 84 096 164 096 324 096 Alg. 2 (energy / min. eig.) 8 9 512 45 512 90 512 180 512 16 21 096 89 096 174 096 344 096 Prop. Alg. EmaxE (max. eig. / energy) 8 9 800 45 800 90 800 180 800 16 18 600 86 600 171 600 341 600 SOME NUMERICAL VALUES OF COMPUTATIONAL COMPLEXITIES FOR SENSING METHODS (M=4, 4x- OVERSAMPLED) ALGORITHMS Smoothing Factor (L) Number of samples (N) 103 5x103 104 2x104 Trad. Alg. Alg. 1 (max. eig. / min. eig.) 8 64 768 192 768 352 768 672 768 16 326 144 582 144 902 144 1 542 144 Alg. 2 (average / min. eig.) 8 68 768 212 768 392 768 752 768 16 330 144 602 144 942 144 1 622 144 Prop. Alg. EmaxE (max. eig. / average) 8 39 200 183 200 363 200 723 200 16 74 400 346 400 686 400 1 366 400
  74. CONCLUSION 78 25.11.2013 ¾ The EMaxE eigenvalue based spectrum sensing

    technique with power iteration has been presented in this paper. ¾ We have analyzed and simulated both false alarm and detection probability performances of the traditional and proposed EmaxE eigenvalue based spectrum sensing methods under different frequency selective channel models. ¾ The overall computational complexity can be reduced from to using the EMaxE algorithm. ¾ When the number of samples is 1000 with and , the overall computational complexity (number of multiplications and additions) of the traditional max/min algorithm is 326144 whereas it is 74400 for the EmaxE algorithm. ¾ Besides Hence upon using the EmaxE algorithm, the complexity is reduced by about 77 percent. Also the sensing performance is clearly improved. 3 (( ) ) O ML ( ) O kML 16 L 4 M
  75. THANK YOU VERY MUCH FOR YOUR LISTENING … Sener Dikmese

    [email protected] Department of Electronics and Communications Engineering Tampere University of Technology 25.11.2013